Fiberglass Canopy for Trex-450 Pro
|
SKU: Trex450P-016
Fiberglass Canopy for; Trex-450 HK-450 And similar helicopters.
|
|
Fiberglass Canopy for Trex-450 Sport
|
SKU: Trex450S-021
Fiberglass Canopy for; Trex-450 HK-450 And similar helicopters.
|
|
High-End Airbrushed Canopy for 450 size Heli
|
SKU: Trex450EX-048
A striking and beautiful canopy! If you take pride in your 450 size machine, than this canopy will not disappoint. Manufactured with stencils and airbrishing for razer-sharp graphics and a high gloss finish.
Canopies are produced from light-weight woven fiberglass, flexible paint and are hand air-brushed.
|
|
Fiberglass Canopy for Trex-500 Electric
|
|
|
High-End Airbrushed Canopy for 500 size Heli
|
SKU: Trex500EX-007
A striking and beautiful canopy! If you take pride in your 500 size machine, than this canopy will not disappoint. Manufactured with stencils and airbrishing for razer-sharp graphics and a high gloss finish.
Canopies are produced from light-weight woven fiberglass, flexible paint and are hand air-brushed.
|
|
Fiberglass Canopy for Trex-250
|
|
|
Fiberglass Canopy for Trex-250
|
|
|
Fiberglass Canopy for Trex-250
|
|
|
Hughes MD500 Fiberglass Fuselage for 450 size heli
|
SKU: HK-0001B11
Hughes MD500 Fiberglass Fuselage for 450 size heli
Beautifully painted and detailed. Complete with transparent canopy, detailed landing gear and magnetic nose for easy battery changes.
Includes mount points for Align T-Rex 450.
Specification Length: 685mm Width: 162mm
Height: 327mm
Weight: 305g
Kits includes all hardware required to install the canopy on a T-Rex 450 (or clone), including extra-long tail servo rod (carbon fiber).
|
|
Hughes MD500 Fiberglass Fuselage for 450 size heli
|
SKU: HK-0001B13
Hughes MD500 Fiberglass Fuselage for 450 size heli
Beautifully painted and detailed. Complete with transparent canopy, detailed landing gear and magnetic nose for easy battery changes.
Includes mount points for Align T-Rex 450.
Specification Length: 685mm Width: 162mm
Height: 327mm
Weight: 305g
Kits includes all hardware required to install the canopy on a T-Rex 450 (or clone), including extra-long tail servo rod (carbon fiber).
|
|
Hughes MD500 Fiberglass Fuselage for 450 size heli
|
SKU: HK-0001B12
Hughes MD500 Fiberglass Fuselage for 450 size heli
Beautifully painted and detailed. Complete with transparent canopy, detailed landing gear and magnetic nose for easy battery changes.
Includes mount points for Align T-Rex 450.
Specification Length: 685mm Width: 162mm
Height: 327mm
Weight: 305g
Kits includes all hardware required to install the canopy on a T-Rex 450 (or clone), including extra-long tail servo rod (carbon fiber).
|
|
Bell 206 Jet Ranger 700-Size
|
KF206NEWS27
The Bell 206 Jet Ranger fuselage for 700 size (60-90 nitro). The fuselage includes detail panel lines and working doors with scale hinges included in the kit. Aluminum scale landing gear are included .Break open design hatch cover and dog house allows easy installation .
The tail section is removable for easy access and installation of mechanics.
Length :1510 mm width :220 mm weight :280 mm (not included landing gear ) Recommend main blades length :660-700 mm
The kit also includes a wooden base with blind nuts for easy installation of a Chaos 600 or Trex 600 helicopters. Tail boom and torque tube extension kit sold separately.
If you plan to use the 600 size mechanics in this fuselage, there is plenty of room for the scale cockpit.
Customers who use this fuse for a 700 size machine will not have enough room for the scale cockpit.
This Video is not intended to encourage people to fly in these conditions. However, it gives you an idea what can happen in 25-30 mph winds.
|
|
EC145 FIRE AND RESCUE SCALE FIBERGLASS FUSELAGE (600-SIZE)
|
|
Item Id: KF145PF6
The new Ver. 3 EC145 Torque Tube Edition..
This kit is designed for the modeler that wants to get in the air quickly. For the average builder, you can get this in the air within 6-8 hrs. This kit includes all the running gear needed for the raised tail system. All you need is to have a working/flying Chaos or Trex 600 heli ( Torque Tube Version )
Cockpit and lighting set sold separately.
|
|
Limited Edition AS350 Black Ops Fiberglass Fuselage (600 Size)
|
Extended Description
|
Highly detailed panel lines and rivets. Professionally painted fuselage with high-gloss automotive finish. Scale landing gear. Scale cockpit complete with seats and console. LED lighting components included. No modification install for TREX600E and Thunder Tiger Raptor 50V2. Fits most other .50 size fuselages See Technical Specs tab for exact dimensions.
Mechanics Compatibility Notes: Direct Fit: Designed to fit ALIGN TREX 600E, and Thunder Tiger Raptor 50V2. There are no mods for TREX 600E and Raptor 50V2. All mounting hardware is provided. Slight Modifications: SWIFT 620SE and other 50 size mechanics. Known Compatibility Issues: ALIGN TREX 600N Although it can be done, it is an issue with the longer boom and longer main frame. The main modification is to extend the mounting board so it fits the frame holes on the longer nitro frame. Does Not Fit: Hirobo Sceadu, Thunder Tiger Raptor 50 Titan; mechanics are too tall for this fuselage. Only previous versions of the .50 raptor and V2 will fit.
|
|
|
NEW ITEM: Bell 212 ERA Scale Fuselage (600 Size)
|
*Does not fit Trex EFL
RC Aerodyne feels that scale does not have to just stop at the outer fuselage. We are pushing the limits and including special designed side frames that allow you to keep all your mechanics up on top in the dog house.
All you need is a flying Trex 600ESP or Chaos 600 torque tube model. That's right, the Bell 212 kit incorporates a torque tube drive tail system. The first of its kind. Just like the real helicopters, this drive system is extremely reliable, maintenance free and is extremely quick to install. No more adjusting, tightening belts, and lubricating drive systems. This is a plug n play system and is a dream to install.
The special designed side frames are designed to offer 2 unique features. 1. To lower the transmission allowing for the torque tube to travel thru the lower tail boom of the helicopter. This has always been an issue with mostly military helicopters. 2. Probably the most revolutionary design in scale helicopters, these frames allow the entire mechanical system to be tucked up inside the dog house just like the real helicopters. This allows for a truly scale helicopter. Normally the mechanics would take up the entire fuselage area, leaving no room for cockpits, rear seats etc.. That's all changed with RC Aerodyne's new frame design. * Note, This does not fit the Trex 600 Pro EFL models
Most of the work is done for you. Pre-drilled holes for easy install of landing gear.
All wood work is installed.
Beautifully painted fiberglass fuselage
Scale cockpit is completely hand assembled and painted for you. All you need to do is just slide it in. No more stickers, each cockpit is hand painted with raised details and instruments. * Cockpit sold separately.
Power set up: Because the Bell 212 is a 2 blade helicopter, there is no need to change any configuration within the mechanics. If you have a healthy flying 600 helicopter, you will not need to upgrade or change anything. Standard 600 set up is a 1100 kv out runner 40mm motor 80-100 amp esc 6s 5000 or higher mah battery pack with a " C " rating of 25 or higher.
Specification: ●Body length:1480mm ( 58.25 " ) ●Body width:330mm ( 13 " ) ●Body high:280mm (11 " )
Included : ●Bell 212 Scale Fuselage ●Upgrade Frame ●Shaf Driven Elevated Tail Rotor Set ●Water Transfer Decals
Cockpit Sold Separately
Required: Flying 600 Chaos/Trex/Variant - * must have torque tube drive system
Scale Rotor Head Sold Separately
|
|
UH-1N Rescue Helicopter Scale Fiberglass Fuselage (600-Size)
|
*Does not fit Trex EFL
RC Aerodyne feels that scale does not have to just stop at the outer fuselage. We are pushing the limits and including special designed side frames that allow you to keep all your mechanics up on top in the dog house.
All you need is a flying Trex 600ESP or Chaos 600 torque tube model. That's right, the Bell UH-1 Twin Huey kit incorporates a torque tube drive tail system. The first of its kind. Just like the real helicopters, this drive system is extremely reliable, maintenance free and is extremely quick to install. No more adjusting, tightening belts, and lubricating drive systems. This is a plug n play system and is a dream to install.
The special designed side frames are designed to offer 2 unique features. 1. To lower the transmission allowing for the torque tube to travel thru the lower tail boom of the helicopter. This has always been an issue with mostly military helicopters. 2. Probably the most revolutionary design in scale helicopters, these frames allow the entire mechanical system to be tucked up inside the dog house just like the real helicopters. This allows for a truly scale helicopter. Normally the mechanics would take up the entire fuselage area, leaving no room for cockpits, rear seats etc.. That's all changed with RC Aerodyne's new frame design. * Note, This does not fit the Trex 600 Pro EFL ,models
Most of the work is done for you. Pre-drilled holes for easy install of landing gear.
All wood work is installed.
Beautifully painted fiberglass fuselage
Scale cockpit is completely hand assembled and painted for you. All you need to do is just slide it in. No more stickers, each cockpit is hand painted with raised details and instruments. * Cockpit sold separately.
Power set up: Because the Bell UH-1N Twin Huey is a 2 blade helicopter, there is no need to change any configuration within the mechanics. If you have a healthy flying 600 helicopter, you will not need to upgrade or change anything. Standard 600 set up is a 1100 kv out runner 40mm motor 80-100 amp esc 6s 5000 or higher mah battery pack with a " C " rating of 25 or higher.
Specification: ●Body length:1480mm ( 58.25 " ) ●Body width:330mm ( 13 " ) ●Body high:280mm (11 " )
Included : ●UH-1N / Bell 212 Scale Fuselage ●Scale Guns for Military Versions ●Upgrade Frame ●Shaf Driven Elevated Tail Rotor Set ●Water Transfer Decals
Cockpit Sold Separately
Required: Flying 600 Chaos/Trex/Variant - * must have torque tube drive system
Scale Rotor Head Sold Separately
|
|
Bell AH-1 Desert Cobra Scale Fuselage W/ Toque Drive System (500 Size)
|
13T pinion 6s 2600-3300mah
Cockpit Sold Separately
|
|
Extended Description
|
|
Additional Information
|
History
Overview
The Bell AH-1 Cobra (company designation: Model 209) is a two-bladed, single engine attack helicopter manufactured by Bell Helicopter. It shares a common engine, transmission and rotor system with the older UH-1 Iroquois. The AH-1 is also referred to as the HueyCobra or Snake.
The AH-1 was the backbone of the United States Army's attack helicopter fleet, but has been replaced by the AH-64 Apache in Army service. Upgraded versions continue to fly with the militaries of several other nations. The AH-1 twin engine versions remain in service with United States Marine Corps (USMC) as the service's primary attack helicopter. Surplus AH-1 helicopters have been converted for fighting forest fires. The United States Forest Service refers to their program as the Firewatch Cobra. Garlick Helicopters also converts surplus AH-1s for forest firefighting under the name, FireSnake.
|
|
|
|
MD500D Little Bird Special Ops Fiberglass Helicopter Fuselage (500-Size)
|
The MH-6 Little Bird, and its attack variant, the AH-6, are single-engine light helicopters used for special operations aviation in the United States Army. Originally based on a modified OH-6A, it was later based on the MD 500E, with a single five-bladed main rotor. The newest version, the MH-6M, is based on the MD 530F and has a single, six-bladed main rotor and four-bladed tail rotor.
The RC Aerodyne Model consists of a large Fiberglass fuslage, weapons set and hardware required to mount your 500 size class machine.
Direct fit for the Chaos 500 and all Align Trex 500
The Front fuselage easily removes by use of locating pins and magnets all ready installed for you as well as all the formers.
The MD500 Series helicopters are the one of the quickest installs. With as little as 3-4 hrs, this scale fuselage can be mounted and flown!
|
|
Eurocopter EC 135 Civilian Fiberglass Fuselage (450 Size)
|
Fits 450 size helicopters
Please note that this fuselage does not have removable front fuselage.
It has access hold for battery on the bottom |
|
Extended Description
|
Highly detailed panel lines and rivets. Professionally painted fuselage with high-gloss automotive finish. |
|
|
|
|